Alien Hydroponics DM Push-Fit Elbow 22mm V-SYSTEM

Quick Spec: SKU BD101-0056 | 22mm Push-Fit | V-SYSTEM Compatible | $8.90 USD

Precision Control in Any Space

Every irrigation run that leaks at a connection point is a compounding liability — nutrient solution lost to the tray floor, root zone moisture variance that no feed schedule can correct after the fact, and maintenance interruptions that pull labor away from canopy management. The enemy is not a single catastrophic failure; it is the slow accumulation of fittings that were never designed to hold tolerance under the thermal cycling and solution chemistry of a live production environment. Barbed connections slip. Threaded adapters weep at the joint. Improvised fittings introduce ID mismatches that restrict flow and create turbulence pockets where sediment accumulates. None of these failure modes announce themselves — they erode consistency quietly, run after run.

After integrating purpose-built V-SYSTEM fittings throughout an irrigation layout, the operational picture changes materially. Every 90-degree direction change in the feed line holds pressure without secondary sealing. Reservoir-to-site delivery stays on the designed flow path. Maintenance windows shrink because connections that seat correctly the first time do not require re-inspection at the start of every cycle. The irrigation system becomes infrastructure that operators trust rather than a variable they manage around.

The mechanism is straightforward: the DM Push-Fit Elbow 22mm is engineered to the dimensional tolerances of the V-SYSTEM tubing platform, meaning the push-fit collet engages the tube wall at the correct depth and the internal O-ring seats against a surface it was designed to contact. The 22mm fitting size matches V-SYSTEM line sizing directly, eliminating the reducer fittings and adapter stacks that introduce leak points in mixed-hardware installations. Compatibility is not incidental — it is the specification. In practical terms, the DM Push-Fit Elbow 22mm V-SYSTEM delivers a tool-free, leak-resistant 90-degree connection in any V-SYSTEM irrigation run at a per-fitting cost of $8.90 USD.

Where This Belongs (and Doesn't)

This fitting is a hydraulic component rated for low-pressure hydroponic irrigation service within the V-SYSTEM platform. It is not rated for pressurized mains supply, high-temperature fluid service, or any application outside its designed compatibility envelope. Verify system operating pressure and fluid temperature against V-SYSTEM platform specifications before installation.

How It Works

The push-fit mechanism operates on a collet-and-O-ring principle. When 22mm V-SYSTEM tubing is inserted into either port of the elbow, the internal collet — a ring of inward-facing gripping teeth — engages the outer wall of the tube and locks it against pull-out force. Simultaneously, the internal O-ring compresses against the tube surface to form a fluid seal without thread compound, clamps, or external tooling. The elbow geometry routes the flow path through a 90-degree arc, allowing the irrigation line to change direction while maintaining the full 22mm bore diameter through the turn.

Disconnection, when required for system reconfiguration, is achieved by depressing the collet release collar at the fitting port while withdrawing the tube — a repeatable operation that does not damage the fitting or the tubing, supporting system modifications without component replacement. The V-SYSTEM compatibility designation means the fitting's internal dimensions are matched to V-SYSTEM tubing OD specifications, which is the critical variable for collet engagement depth and O-ring sealing surface contact. Using this fitting with tubing outside the V-SYSTEM dimensional standard will compromise both the mechanical lock and the fluid seal. In practical terms, the DM Push-Fit Elbow 22mm V-SYSTEM provides a tool-free, reconfigurable 90-degree connection point rated to V-SYSTEM platform specifications at SKU BD101-0056 for $8.90 USD per fitting.

System Integration

• V-SYSTEM Tubing Compatibility: Designed exclusively for 22mm V-SYSTEM tubing — verify tubing OD before installation to confirm dimensional match with the push-fit collet
• No-Tool Installation: Push-fit connection requires no wrenches, thread tape, or clamp hardware; insertion and release are manual operations
• Irrigation Architecture: Functions as a direction-change node in top-feed, drain-to-waste, and recirculating layouts wherever the feed line must route around physical obstructions or change plane
• Reservoir Integration: Compatible with V-SYSTEM reservoir outlet and manifold configurations that use 22mm line sizing throughout the distribution network
• System Expansion: Supports modular layout changes — fittings can be disconnected and reused when reconfiguring grow space without replacing tubing or fittings

Facility Integration Data

The per-unit cost of $8.90 USD makes the DM Push-Fit Elbow 22mm V-SYSTEM a low-friction line item in any V-SYSTEM infrastructure build or maintenance budget; the table below reflects total fitting cost at common fleet quantities for procurement planning.

Operator Field Notes

• Confirm tubing OD before ordering: Push-fit collet engagement is dimensionally specific — 22mm V-SYSTEM tubing is the correct match; substituting non-V-SYSTEM tubing of nominally similar size risks incomplete collet engagement and seal failure
• Seat the tube fully: Insert tubing until it bottoms against the internal tube stop; partial insertion leaves the O-ring unseated and will result in a slow leak under operating pressure
• Inspect O-rings on used fittings: When reusing fittings after system reconfiguration, visually inspect the internal O-ring for deformation or chemical degradation before reinstalling in a live irrigation run
• Flush before commissioning: Run clean water through newly assembled V-SYSTEM lines before introducing nutrient solution to verify all push-fit connections are leak-free under operating flow conditions
• Stock spares for active facilities: At $8.90 per unit, maintaining a small inventory of replacement elbows eliminates downtime when a fitting requires replacement mid-cycle
• Release collar technique: To disconnect, depress the collet release collar squarely and evenly while withdrawing the tube in a straight line — angled withdrawal can bind the collet and require more force than necessary

Shipping & Logistics

• Shipping Jurisdiction: Cannafull Spectrum Solutions ships within the contiguous 48 United States only. Orders outside this region cannot be fulfilled.
• Fulfillment: Orders are processed and shipped from our fulfillment operation; estimated transit times will be provided at checkout based on destination.
• Returns: Returns are accepted subject to the conditions outlined in the Cannafull Spectrum Solutions Return Policy. Items must be in original, uninstalled condition to qualify for return consideration.
• Restocking Fee: Returns of non-defective items are subject to a restocking fee of up to 25% per our Return Policy. Review full terms at cannafullspec.com/pages/return-policy before ordering.

Questions about your order? Contact Cannafull Spectrum Solutions at cannafullspec.com or reach the team directly through the site contact page.

What's in the Box

• 1x DM Push-Fit Elbow 22mm V-SYSTEM (SKU BD101-0056)

Box contents confirmed from available source data. No additional accessories, tubing, or hardware are listed as included with this SKU. If your application requires V-SYSTEM tubing, manifolds, or additional fittings, these must be sourced separately. Contact Cannafull Spectrum Solutions to confirm current packaging before ordering if complete kit contents are critical to your procurement decision.

Regional Compliance & Deployment Notes

• Jurisdiction: This product is available for sale and shipment within the contiguous 48 United States only through Cannafull Spectrum Solutions.
• Facility Compliance: The DM Push-Fit Elbow 22mm V-SYSTEM is a hydraulic irrigation fitting. Operators are responsible for ensuring that their irrigation system design, installation, and operation comply with all applicable local, state, and facility-level regulations governing water use, nutrient solution handling, and drainage in licensed production environments.
• No Electrical or Structural Rating: This fitting carries no electrical safety certification and is not rated for structural, pressurized mains, or high-temperature service. Deploy only within the V-SYSTEM platform's specified operating parameters.
• Operator Responsibility: Installation, system commissioning, and ongoing maintenance of V-SYSTEM irrigation infrastructure are the responsibility of the operating facility. Cannafull Spectrum Solutions provides product supply and pre-purchase technical support but does not provide on-site installation services.

Product specifications, compatibility designations, and pricing are subject to change by the manufacturer without notice. All information presented reflects available source data at time of publication. Verify current specifications with Cannafull Spectrum Solutions before finalizing procurement decisions for facility-scale installations.