AC Infinity Peel and Stick Zipper | 7 ft. x 3 in. Double Sided | 1-Pack

Quick Spec: Total Size: 3.00 in. x 7 ft. (7.62 x 213.4 cm)  |  Material: Nylon  |  Zipper Type: SBS Double-Sided  |  SKU: AC-SZA4-1  |  UPC: 819137022553

Precision Control in Any Space.

Every unsealed gap in a partitioned grow environment is a liability. A loose flap, a slit held shut with tape, a pass-through that never quite closes — these are not minor inconveniences. They are uncontrolled variables bleeding humidity out of the zones where it needs to stay, pulling dust and debris into spaces that demand sterility, and creating pressure differentials that undermine every atmospheric investment you have made in fans, filters, and environmental controllers. The enemy is not a single failure point. It is the accumulation of small, ignored breaches that quietly erode the consistency you are trying to build. Every time a worker pushes through an unsealed barrier, the environment resets in ways that are difficult to measure and impossible to fully recover from within a single cycle.

After deployment, the partition becomes an asset rather than a weak point. Workers move between zones through a defined, closeable aperture that re-seals behind them without a second thought. Humidity stays where it was dialed in. Dust and particulate matter stay on the other side of the barrier. Odor containment holds. The atmospheric conditions you have engineered into each zone remain stable across traffic events rather than degrading with every entry. The barrier layer — whether panda film, poly sheeting, or vinyl — functions as a true environmental boundary instead of a suggestion.

The mechanism is a high-temperature nylon adhesive strip measuring 3.00 in. x 7 ft. (7.62 x 213.4 cm) with a peel-and-stick backing that bonds directly to tarps, poly film, panda film, and vinyl sheeting. The SBS (Slide Both Sides) double-sided zipper design provides pull tabs accessible from either face of the barrier, enabling entry or exit from both sides without requiring a second person or a second zipper installation. The jam-proof zipper track maintains consistent engagement across repeated open-and-close cycles, and the nylon construction tolerates the elevated ambient temperatures common in high-density cultivation environments. The adhesive seal, once set, creates an air and watertight closure that contains humidity, blocks dust and debris ingress, and reduces light leak at the partition seam. In practical terms, the AC Infinity Peel and Stick Zipper delivers a 7-foot sealed access point across a 3-inch-wide adhesive footprint on any compatible plastic sheeting surface, with no tools, fasteners, or framing required.

Where This Belongs (and Doesn't)

This product is a mechanical barrier accessory. It does not replace environmental controllers, atmospheric sensors, or HVAC infrastructure. Adhesive bond strength is dependent on surface cleanliness, surface type, and ambient temperature at time of application. Verify surface compatibility before installation in critical containment applications.

How It Works

The AC Infinity Peel and Stick Zipper operates on a straightforward adhesive-and-track system that requires no tools, no sewing, and no mechanical fasteners. The nylon strip is backed with a pressure-sensitive adhesive rated for high-temperature environments — the same thermal conditions generated by high-intensity lighting arrays and dense canopy environments. To install, the operator cleans the target surface, peels the backing from the adhesive strip, and presses the nylon track firmly onto the plastic sheeting. The strip bonds to tarps, poly film, panda film, and vinyl sheeting, creating a permanent mounting channel for the zipper track along the full 7-foot (213.4 cm) length.

The SBS (Slide Both Sides) zipper mechanism is the operational core of the system. Unlike single-pull zippers that require access from one designated face, the double-sided pull tab configuration allows any person on either side of the barrier to open or close the access point independently. This eliminates the operational bottleneck of one-way-only entries in high-traffic partition scenarios. The jam-proof track geometry maintains consistent slider engagement across repeated cycles, reducing the maintenance overhead associated with conventional zipper hardware that degrades under frequent use in humid environments. The closed zipper creates an air and watertight seal along the full seam length, containing humidity within the target zone, blocking dust and debris from crossing the barrier, and reducing light transmission at the partition seam when used with opaque sheeting such as panda film. In practical terms, the AC Infinity Peel and Stick Zipper installs in minutes onto any compatible plastic sheeting surface and delivers a repeatable, dual-access sealed aperture measuring 3.00 in. x 7 ft. (7.62 x 213.4 cm) across its full bonded length.

System Integration

• Panda Film Barriers: Bonds directly to panda film partition walls to create sealed, dual-access entry points that reduce light leak and contain humidity and odor within the target zone.
• Poly Film and Tarp Enclosures: Compatible with standard poly sheeting and tarp materials used in temporary grow room construction and multi-zone facility partitioning.
• Atmospheric Control Infrastructure: Supports the integrity of sealed zones managed by inline fans, carbon filters, and environmental controllers by eliminating uncontrolled air exchange at partition seams.
• Multi-Zone Facility Layouts: Enables controlled personnel movement between partitioned cultivation zones without compromising the atmospheric boundary established by the barrier layer.
• Containment and Remediation Applications: Applicable in facility buildout, remediation enclosures, and temporary containment structures where plastic sheeting is the primary barrier material.

Operator Field Notes

• Surface Prep is Non-Negotiable: Adhesive bond strength is directly dependent on surface cleanliness at time of application. Wipe the target area with isopropyl alcohol and allow it to dry completely before pressing the nylon strip into place. Dust, moisture, or residue on the sheeting surface will compromise long-term adhesion.
• Temperature at Application Matters: Apply in ambient conditions consistent with normal facility operating temperatures. Applying to cold or condensation-covered sheeting reduces initial tack and may result in edge lift over time.
• Panda Film Compatibility: The adhesive strip bonds to the white face of panda film. Confirm the installation face before peeling the backing — repositioning after contact is not recommended as it degrades adhesive performance.
• Zipper Engagement Check: After installation, run the zipper slider through the full 7-foot length in both directions before putting the access point into service. This seats the track and confirms there are no adhesion gaps along the seam that could compromise the air and watertight seal.
• High-Traffic Zones: In zones with frequent personnel movement, inspect the adhesive perimeter edges monthly. Edge lift at high-traffic access points is the primary failure mode — address with compatible adhesive tape at the strip edges if early separation is observed.
• Single-Use Adhesive: The peel-and-stick backing is a one-time application system. Plan installation location carefully. Removal and reinstallation on a new surface is not supported by the adhesive system and will require a replacement unit.

Shipping & Logistics

• Shipping Jurisdiction: Cannafull Spectrum Solutions ships within the contiguous 48 United States only. Orders outside this jurisdiction cannot be fulfilled through this storefront.
• Fulfillment: Orders are processed and shipped from authorized distribution points. Estimated lead times are displayed at checkout and are subject to carrier conditions and order volume.
• Returns: Returns are accepted for unopened, non-defective units in original packaging. Adhesive-backed products that have had the backing removed or have been applied to a surface are not eligible for return. Contact support@cannafullspec.com to initiate a return authorization before shipping any unit back.
• Restocking Fee: Returns of non-defective items are subject to a restocking fee of up to 25% per our Return Policy. Review full terms at cannafullspec.com/pages/return-policy before ordering.

Questions about your order? Contact Cannafull Spectrum Solutions at support@cannafullspec.com or visit cannafullspec.com for current lead times and order status.

What's in the Box

• 1x AC Infinity Peel and Stick Zipper — 3.00 in. x 7 ft. (7.62 x 213.4 cm), Nylon, SBS Double-Sided (SKU: AC-SZA4-1)

Note: Box contents confirmed from manufacturer source data. No additional hardware, adhesive tools, or installation accessories are listed as included. Plastic sheeting, panda film, poly film, or tarp materials are not included and must be sourced separately. Verify package contents upon receipt and contact support@cannafullspec.com immediately if any discrepancy is identified.

Regional Compliance & Deployment Notes

• Jurisdiction: This product is sold and shipped within the contiguous 48 United States only through Cannafull Spectrum Solutions. No international fulfillment is available through this storefront.
• Regulatory Classification: The AC Infinity Peel and Stick Zipper is a mechanical barrier accessory. It is not subject to electrical, HVAC, or emissions compliance standards. No UL, ETL, or FCC certification is applicable to this product category.
• Facility Compliance: Operators are responsible for ensuring that partition barrier systems — including the sheeting materials to which this zipper is applied — comply with any applicable state or local fire code, building code, or controlled-environment facility licensing requirements in their jurisdiction. This product does not carry fire-rated barrier certification.
• State-Level Licensing: Deployment in licensed cultivation facilities is the responsibility of the facility operator. Cannafull Spectrum Solutions makes no representation regarding the suitability of this product for compliance with any specific state cannabis facility licensing standard. Consult your facility compliance officer before specifying barrier materials and access hardware for licensed spaces.
• Contiguous U.S. Deployment: This product is actively deployed in licensed commercial cultivation facilities across the United States. Cannafull Spectrum Solutions does not ship to Alaska, Hawaii, U.S. territories, or any address outside the contiguous 48 states.

Product specifications, pricing, warranty terms, and availability are subject to change without notice. All data presented on this page is sourced from manufacturer documentation current at time of publication. Cannafull Spectrum Solutions is a factory-authorized dealer of AC Infinity products. Verify current specifications and warranty terms at cannafullspec.com or by contacting support@cannafullspec.com prior to purchase.