Alien 水培涡流泵进气歧管 40 毫米长

Quick Spec: SKU BD101-0029  |  Length: 40mm  |  Compatibility: V-SYSTEM  |  Price: $47.74

Precision Control in Any Space

When the inlet side of a hydroponic system is left to chance — wrong-length manifolds, generic fittings sourced from unrelated platforms, or components that were never designed to work together — the entire irrigation circuit absorbs that disorder. Flow rates drift between sites. Reservoir pressure fluctuates. Feed schedules that look correct on paper produce uneven uptake across the canopy because the water never arrives with the consistency the nutrient program demands. The cost is not always visible in a single cycle; it accumulates quietly in yield variance, extended veg times, and the diagnostic hours spent chasing a problem that was built into the system from the first connection.

After integrating the correct OEM inlet manifold, the irrigation circuit behaves as a unified system rather than a collection of approximations. Each feed event delivers the same hydraulic conditions to the same points in the reservoir assembly. Top-feed lines charge at the pressure the pump was calibrated to produce. Drain-to-waste cycles complete on schedule because there is no restriction or turbulence introduced by a mismatched fitting. The operator stops troubleshooting the plumbing and starts managing the crop.

The mechanism is dimensional precision. At 40mm in length, this manifold occupies the exact inlet geometry the V-SYSTEM pump housing was engineered to accept — no shimming, no thread adapters, no compensating for a component that was never meant to be there. The 40mm specification is not an approximation; it is the OEM-matched length that preserves the hydraulic relationship between the pump inlet and the reservoir feed path. Compatibility is confirmed for V-SYSTEM platforms, and the manifold is available for direct pickup in Longmont for operators who need same-day integration into an active system. In practical terms, the Vortex Pump Inlet Manifold 40mm delivers OEM-matched inlet geometry across V-SYSTEM irrigation assemblies at a single-unit price of $47.74.

Where This Belongs (and Doesn't)

This manifold is a hydraulic fitting component. Installation should be performed by operators familiar with V-SYSTEM plumbing architecture. Verify system pressure ratings and pump compatibility before integration. Not intended for use outside the V-SYSTEM platform without independent engineering review.

How It Works

The Vortex Pump Inlet Manifold functions as the hydraulic interface between the pump inlet port and the reservoir feed path within the V-SYSTEM architecture. Its 40mm length is the governing dimension: it determines the seating depth of the manifold within the pump housing, which in turn controls the cross-sectional flow area presented to the incoming fluid. When that dimension is correct, the pump operates within its designed hydraulic envelope — inlet velocity, pressure recovery, and flow uniformity all remain within the parameters the system was calibrated to produce.

Substituting a manifold of incorrect length — even by a few millimeters — alters the effective inlet bore geometry. The pump may cavitate at lower flow rates, or the inlet may not seat fully, introducing a leak path or a turbulence zone that degrades feed consistency across the irrigation circuit. The 40mm specification eliminates that variable entirely by restoring the OEM inlet condition. For operators running top-feed or drain-to-waste configurations where feed timing and volume are tightly managed, maintaining the correct inlet geometry is a prerequisite for the nutrient delivery program to perform as designed. In practical terms, the Vortex Pump Inlet Manifold 40mm restores OEM inlet geometry to V-SYSTEM pump assemblies, preserving hydraulic consistency across every feed event in the irrigation cycle.

Commercial Assurance

System Integration

• Platform Requirement: Designed exclusively for V-SYSTEM hydroponic platforms; confirm pump model compatibility before ordering
• Inlet Length: 40mm — verify against existing manifold or pump housing specification before replacement
• Circuit Types: Compatible with top-feed, drain-to-waste, and recirculating reservoir configurations within the V-SYSTEM
• Maintenance Integration: Suitable for scheduled preventive replacement cycles on active irrigation systems
• Sourcing: Available for immediate pickup in Longmont or direct order through Cannafull Spectrum Solutions

Facility Integration Data

For facilities operating multiple V-SYSTEM units, maintaining a stock of OEM inlet manifolds reduces unplanned downtime during irrigation system servicing — the table below reflects per-unit and fleet-level procurement cost at current MAP pricing.

Operator Field Notes

• Confirm the 40mm length against your existing pump inlet manifold before ordering — the V-SYSTEM platform uses multiple manifold lengths and an incorrect substitution will affect inlet seating and flow performance
• Inspect the pump housing inlet port for wear or debris before installing a replacement manifold; a clean seating surface is required for the OEM fit to perform as designed
• For facilities running timed top-feed schedules, replace inlet manifolds as part of a scheduled maintenance interval rather than waiting for a failure event — unplanned irrigation downtime during active feed cycles carries a higher operational cost than a proactive component swap
• Longmont pickup is available for operators who need same-day component access; contact Cannafull Spectrum Solutions to confirm stock availability before making the trip
• If warranty coverage is a procurement requirement for your facility, request written confirmation of terms from Cannafull Spectrum Solutions prior to purchase, as warranty data is not specified in current manufacturer source documentation

Operator FAQ

Shipping & Logistics

• Shipping Region: Cannafull Spectrum Solutions ships within the contiguous 48 United States only. Orders outside this region cannot be fulfilled.
• Local Pickup: Available in Longmont, Colorado. Contact us to confirm stock availability and arrange pickup timing before placing your order.
• Returns: Component returns are subject to our standard return policy. Items must be uninstalled and in original condition. Contact Cannafull Spectrum Solutions within the applicable return window to initiate a return authorization.
• Restocking Fee: Returns of non-defective items are subject to a restocking fee of up to 25% per our Return Policy. Review full terms at cannafullspec.com/pages/return-policy before ordering.

Questions about shipping, pickup, or returns? Contact Cannafull Spectrum Solutions directly before ordering.

What's in the Box

• 1x Vortex Pump Inlet Manifold — 40mm Long (SKU: BD101-0029)

Box contents reflect manufacturer packaging as documented in available source data. Additional hardware, fittings, or installation accessories are not confirmed as included. If your application requires supplementary components, verify the complete bill of materials with Cannafull Spectrum Solutions before ordering.

Regional Compliance & Deployment Notes

• This product is sold and shipped within the contiguous 48 United States only by Cannafull Spectrum Solutions.
• The Vortex Pump Inlet Manifold 40mm is a hydraulic plumbing component. Installation must comply with applicable facility plumbing and irrigation codes in the operator's jurisdiction.
• No electrical, chemical, or controlled-substance compliance certifications are associated with this component based on available source data.
• Operators in jurisdictions with specific requirements for irrigation system components in licensed cultivation facilities should verify local compliance obligations independently before installation.
• Cannafull Spectrum Solutions does not ship to Canadian provinces or territories. No CSA certification or Health Canada compliance language applies to this listing.

Compliance requirements vary by state and facility license type. The information provided here reflects available manufacturer documentation and does not constitute legal or regulatory advice. Operators are responsible for verifying that all installed components meet the requirements of their applicable facility license and jurisdiction.