Alien Hydroponics DM 推入式弯头 22-15 毫米 V-SYSTEM

Quick Spec: SKU BD101-0057 | Fitting Type: Push-Fit Elbow | Size: 22-15mm | System: V-SYSTEM | Price: $8.90 USD

Precision Control in Any Space

Every irrigation circuit has a failure point, and in space-constrained production environments, that failure point is almost always a fitting. Threaded connections back out under vibration. Barbed adapters require clamps that corrode. Improvised directional transitions introduce micro-gaps that allow nutrient solution to wick, drip, and contaminate the root zone without triggering an obvious alarm. The cost is not a single catastrophic flood — it is the slow, invisible variance that accumulates across every feed cycle: inconsistent delivery pressure, uneven saturation, and the operational drag of tracing a leak that should never have existed.

After integrating purpose-built push-fit fittings into the V-SYSTEM feed circuit, the irrigation infrastructure behaves as a closed, predictable system. Directional transitions hold under pressure without secondary sealing. Feed lines route cleanly through tight vertical and horizontal runs. Operators stop troubleshooting connections and start reading data — because the data is no longer contaminated by mechanical inconsistency at the fitting level. The reservoir delivers what it is programmed to deliver, every cycle, without manual intervention at the junction point.

The DM Push-Fit Elbow 22-15mm V-SYSTEM achieves this through a push-fit locking mechanism engineered to V-SYSTEM dimensional tolerances, providing a secure 22mm-to-15mm directional transition that seats on insertion and releases only on deliberate tool-assisted disconnection. Compatibility is confirmed for V-SYSTEM infrastructure, eliminating the guesswork of cross-system fitting substitution that introduces dimensional mismatch and seal failure. In practical terms, the DM Push-Fit Elbow 22-15mm V-SYSTEM delivers a sealed, tool-free directional transition at the 22-to-15mm junction within V-SYSTEM irrigation circuits at a unit cost of $8.90 USD.

Where This Belongs (and Doesn't)

This fitting is a mechanical irrigation component rated for V-SYSTEM hydroponic infrastructure. It is not an electrical component and carries no voltage, current, or pressure rating beyond the V-SYSTEM manufacturer's specified operating parameters. Do not substitute this fitting in pressurized systems operating outside V-SYSTEM design specifications without consulting the system manufacturer.

How It Works

The push-fit mechanism operates on a collet-and-O-ring principle: inserting the tubing into the fitting body compresses an internal collet ring that grips the outer diameter of the tube, while a seated O-ring forms the fluid seal at the insertion point. The result is a connection that requires no tools to make, no clamps to torque, and no thread compound to apply. The 22-to-15mm reducer geometry allows the fitting to serve as both a directional elbow and a diameter transition in a single component, reducing the number of inline connection points required to route feed lines around obstacles in tight grow infrastructure.

Disconnection is deliberate by design: a release collar on the fitting body must be depressed to disengage the collet grip, preventing accidental pull-out under normal operating tension on the feed line. This release mechanism allows the fitting to be reused across system reconfigurations without degrading the seal integrity of the collet, provided the tubing end is cut cleanly and squarely on reinstallation. V-SYSTEM compatibility is confirmed at the manufacturer level, meaning the collet and O-ring dimensions are matched to V-SYSTEM tubing outer diameters — not approximated from generic push-fit stock. In practical terms, the DM Push-Fit Elbow 22-15mm V-SYSTEM provides a reusable, tool-free 22-to-15mm directional transition with a manufacturer-confirmed fit to V-SYSTEM tubing tolerances at $8.90 USD per unit.

System Integration

• Integrates directly into V-SYSTEM top-feed and drain-to-waste irrigation circuits at 22mm-to-15mm directional transition points.
• Push-fit connection eliminates the need for thread tape, barb clamps, or secondary sealing compounds at the elbow junction.
• Reusable collet mechanism supports system reconfiguration without requiring replacement fittings on each rebuild cycle.
• Single-component 22-to-15mm reducer elbow reduces inline connection count compared to two-piece adapter-plus-elbow assemblies.
• Confirmed dimensional match to V-SYSTEM tubing outer diameters ensures seal integrity without operator-side tolerance verification.

Facility Integration Data

The following table provides procurement reference data for operators scaling V-SYSTEM irrigation infrastructure across multi-site or multi-room deployments, based on a unit cost of $8.90 USD per fitting.

Operator Field Notes

• Cut tubing ends cleanly and squarely before insertion — angled or ragged cuts compromise the O-ring seal and reduce collet grip surface contact.
• Insert tubing to full depth until it bottoms out against the internal stop; partial insertion is the primary cause of push-fit connection failure under feed pressure.
• To disconnect, depress the release collar fully before applying pull force — forcing the tube out without collar depression damages the collet and voids reusability.
• Inspect the O-ring seat for debris or mineral buildup during each system flush cycle; nutrient salt accumulation at the seal face is the leading cause of slow-drip failure in push-fit irrigation fittings.
• Maintain a minimum spare inventory of push-fit elbows equal to 10% of installed fitting count per production zone to support unscheduled reconfiguration without procurement delays.
• Confirm V-SYSTEM tubing outer diameter at the specific run being fitted — tubing from non-V-SYSTEM sources may share nominal sizing but differ in actual OD, causing collet undergrip.

Operator FAQ

Shipping & Logistics

• Shipping Jurisdiction: Cannafull Spectrum Solutions ships within the contiguous 48 United States only. Orders outside this jurisdiction cannot be fulfilled.
• Fulfillment: SKU BD101-0057 ships from Cannafull Spectrum Solutions inventory. Processing and transit times are confirmed at order placement. Contact cannafullspec.com for current lead times on quantity orders.
• Returns: Returns are accepted subject to the Cannafull Spectrum Solutions Return Policy. Items must be in original, uninstalled condition. Installed fittings are not eligible for return.
• Restocking Fee: Returns of non-defective items are subject to a restocking fee of up to 25% per our Return Policy. Review full terms at cannafullspec.com/pages/return-policy before ordering.

For commercial procurement, quantity pricing, or logistics coordination: cannafullspec.com

What's in the Box

• 1x DM Push-Fit Elbow 22-15mm V-SYSTEM fitting (SKU BD101-0057)

Box contents are confirmed from manufacturer source data. No additional accessories, tubing, or installation hardware are listed as included. Verify complete system component requirements against V-SYSTEM documentation prior to ordering to ensure all required fittings and tubing are procured in a single order cycle.

Regional Compliance & Deployment Notes

• This product is a mechanical irrigation fitting. It is not subject to electrical safety certification (UL, ETL, CE) requirements.
• Deployment in licensed production facilities should be verified against applicable state and local plumbing or irrigation codes governing nutrient delivery systems in commercial agricultural or controlled-environment agriculture settings.
• No federal or state registration is required for push-fit irrigation fittings in the United States. Confirm local jurisdiction requirements with your compliance officer prior to facility buildout.
• Cannafull Spectrum Solutions ships and supports deployment within the contiguous 48 United States only. No Canadian distribution, CSA certification, or Health Canada compliance documentation is applicable to this product as sold through this channel.
• V-SYSTEM is a manufacturer-designated product line. Confirm current V-SYSTEM compatibility documentation with the manufacturer for any regulatory or insurance compliance requirements specific to your facility's irrigation infrastructure specifications.

Product specifications, compatibility claims, and pricing are based on manufacturer-published source data current at time of listing. Cannafull Spectrum Solutions makes no representations beyond confirmed manufacturer data. Verify all specifications against current manufacturer documentation prior to procurement for regulated facility applications. Pricing subject to change without notice.