Alien Hydroponics 28 毫米推入式止动端

Precision Control in Any Space

Every unused port in a live irrigation circuit is a liability. When a line termination point is not properly sealed — whether it is a capped branch on a top-feed manifold or an idle outlet on a drain-to-waste header — the result is not neutral. Pressure bleeds. Nutrient solution wicks. Residual moisture accumulates at the fitting interface and becomes a vector for contamination between runs. The enemy is not a catastrophic failure; it is the slow, invisible cost of fittings that were never designed to work together, improvised solutions that hold until they do not, and the run-to-run variance that follows when your irrigation circuit is not fully closed.

After proper termination with a system-matched stop end, the circuit behaves as designed. Every active feed line delivers its programmed volume. Unused ports contribute nothing — no drip, no pressure loss, no contamination pathway. Between runs, the manifold flushes clean because there are no improvised caps trapping residual solution in dead-end pockets. The operator gains confidence that what the controller schedules is what the root zone receives, run after run, without manual inspection of every termination point before lights-on.

The 28mm Push-Fit Stop End achieves this through direct mechanical compatibility with the Alien Hydroponics V-SYSTEM platform. The push-fit engagement mechanism is sized and toleranced to the V-SYSTEM's 28mm port specification, meaning the fitting seats fully on insertion without tools, thread tape, or secondary sealing compounds. Compatibility is not approximate — it is manufacturer-matched. The stop end terminates the line at the port, not downstream of it, eliminating the dead-leg volume that accumulates in non-flush termination designs. In practical terms, the 28mm Push-Fit Stop End delivers a fully sealed, pressure-stable termination at any unused V-SYSTEM port for $9.20 per fitting with no additional sealing materials required.

Where This Belongs (and Doesn't)

This fitting is a plumbing component rated for low-pressure irrigation service within the Alien Hydroponics V-SYSTEM. It is not rated for pressurized mains, potable water supply lines, or any application outside the V-SYSTEM platform. Do not use as a substitute for pressure-rated fittings in non-irrigation circuits.

How It Works

The push-fit mechanism operates on a collet-and-seal principle standard to professional irrigation fittings. When the stop end is inserted into a V-SYSTEM 28mm port, an internal collet ring grips the port wall and an elastomeric seal compresses against the bore to create a leak-free closure. No tools are required for installation. Removal, where the fitting design permits, is achieved by depressing the collet release collar and withdrawing the fitting — allowing the operator to reconfigure the circuit without cutting tubing or replacing fittings.

Because the stop end is manufacturer-matched to the V-SYSTEM's 28mm port geometry, the collet engagement depth and seal compression are within the tolerances Alien Hydroponics specifies for leak-free performance. Off-system fittings introduce dimensional variance at the collet interface that can result in incomplete seating, reduced grip force, and seal bypass under operating pressure. System-matched termination eliminates that variable entirely. In practical terms, the 28mm Push-Fit Stop End installs in seconds at any unused V-SYSTEM port and holds a leak-free seal under normal irrigation operating pressures without supplemental sealing materials.

Commercial Assurance

• Manufacturer Compatibility: Factory-specified for Alien Hydroponics V-SYSTEM 28mm ports — not a generic fitting adapted to fit.
• Authorized Distribution: Sold through Cannafull Spectrum Solutions as a factory-authorized dealer. Authenticity is guaranteed at point of sale.
• Warranty: Warranty terms are not specified in available source data. Contact Cannafull Spectrum Solutions at cannafullspec.com for current warranty information before ordering.
• Local Availability: Available for in-person pickup at our Longmont location — no shipping lead time for local operators.
• Flexible Payment: Available in 4 payments of $2.30 USD via Sezzle for qualifying orders.

System Integration

• V-SYSTEM Manifold Compatibility: Seats directly into any 28mm V-SYSTEM port without adapters, thread tape, or secondary sealants.
• Top-Feed Circuit Integrity: Eliminates pressure bleed at unused manifold outlets, ensuring programmed feed volumes reach only active zones.
• Drain-to-Waste Reservoir Systems: Caps idle branch lines between runs to prevent residual solution accumulation and cross-contamination.
• Flush and Sanitation Cycles: Allows operators to isolate and seal inactive circuit segments during between-run cleaning without disassembling the manifold.
• Scalable Deployment: Priced at $9.20 per unit, making it practical to stock multiples for full-circuit termination across multi-zone V-SYSTEM installations.

Facility Integration Data

For operators managing multi-zone V-SYSTEM installations, the per-unit cost of proper termination is negligible relative to the feed variance and contamination risk introduced by unmatched or improvised stop ends — the table below illustrates total termination cost at scale.

Pricing based on $9.20 MAP per unit (SKU BD101-0034). Volume pricing not confirmed in source data — contact Cannafull Spectrum Solutions for current bulk availability.

Operator Field Notes

• Stock multiples before you need them: At $9.20 per unit, running short of stop ends mid-reconfiguration is an avoidable delay — keep a working inventory on hand for any V-SYSTEM installation with more ports than active feed lines.
• Inspect the port before insertion: Push-fit seals require a clean, undamaged port bore. Debris or deformation at the port rim will compromise collet engagement and seal compression — wipe ports clean before fitting installation.
• Do not force a non-seating fitting: A properly matched 28mm stop end seats with firm hand pressure. Resistance before full engagement indicates a port obstruction or dimensional mismatch — do not force the fitting or use tools to drive it home.
• Verify seal integrity before pressurizing: After installing stop ends on any reconfigured circuit segment, run a low-pressure check before returning to full operating pressure. A visual inspection at each termination point takes less than a minute and confirms seal engagement.
• Local pickup eliminates lead time: For operators in the Longmont area, in-person pickup means same-day availability — no waiting on shipping when a run is scheduled and a fitting is needed.

Operator FAQ

Shipping & Logistics

• Shipping Jurisdiction: Cannafull Spectrum Solutions ships within the contiguous 48 United States only. Orders outside this region cannot be fulfilled through our platform.
• Local Pickup: Available at our Longmont, Colorado location. Contact us through cannafullspec.com to confirm stock before visiting.
• Returns: Returns are accepted subject to our Return Policy. Items must be in original, uninstalled condition. Contact cannafullspec.com to initiate a return authorization before shipping any product back.
• Restocking Fee: Returns of non-defective items are subject to a restocking fee of up to 25% per our Return Policy. Review full terms at cannafullspec.com/pages/return-policy before ordering.

Questions about your order? Contact Cannafull Spectrum Solutions at cannafullspec.com.

What's in the Box

• 1x Alien Hydroponics 28mm Push-Fit Stop End (SKU BD101-0034)

Note: Box contents are confirmed based on available source data. No additional accessories, documentation, or hardware are listed in the manufacturer's product specification for this SKU. If your shipment is missing any components, contact Cannafull Spectrum Solutions before installation.

Regional Compliance & Deployment Notes

• Jurisdiction: This product is sold and shipped within the contiguous 48 United States only through Cannafull Spectrum Solutions.
• Plumbing Classification: The 28mm Push-Fit Stop End is classified as a low-pressure irrigation fitting for use within the Alien Hydroponics V-SYSTEM. It is not a potable water fitting and is not subject to NSF/ANSI 61 or equivalent potable water compliance standards in its intended application.
• Facility Compliance: Operators are responsible for ensuring that all irrigation system components, including fittings and termination hardware, comply with applicable state and local regulations governing commercial cultivation facility plumbing and water management systems.
• No Canadian Distribution: Cannafull Spectrum Solutions does not ship to Canadian provinces. This product listing does not reference Health Canada compliance, CSA certification, or any Canadian regulatory framework.
• Licensed Facility Use: This product is deployed in licensed commercial cultivation facilities across the United States operating V-SYSTEM irrigation infrastructure.

Product specifications, compatibility claims, and regulatory classifications are based on available manufacturer source data at time of publication. Cannafull Spectrum Solutions makes no representations beyond what is confirmed in manufacturer documentation. Verify current specifications and compliance requirements with Alien Hydroponics and applicable regulatory authorities before deployment in regulated facilities.