AC Infinity IONBEAM S16 | 全光谱 LED 生长灯条 | 三星 LM301H | 16 英寸

Key Specs: 42W | 3.14 µmol/J PPE | Four 16" Bars | Samsung LM301H EVO | IP65 | 50,000 Hr Lifespan | 2-Year Warranty

Kill Variance. Print Yield.

Every facility running primary overhead fixtures alone is operating with a structural blind spot. Legacy HPS infrastructure casts hard shadows into the lateral canopy, and passive failure points — degrading lamp output, manual dimming schedules, unmonitored dead zones — compound silently across every cycle. The variance tax is not a single catastrophic event; it is the steady erosion of uniformity at the canopy edges, the lower bud sites that never reach density, and the yield gap that never gets attributed to its actual cause. No alarm fires. No report flags it. The facility just underperforms, cycle after cycle, while the root cause remains invisible inside the light map.

After deployment of the IONBEAM S16 kit, the facility operates with a closed canopy light model. Every lateral zone, every inter-canopy corridor, every lower bud site receives a scheduled, dimmable photon dose from bars positioned exactly where overhead fixtures cannot reach. The controller runs automated ON/SCHEDULE/OFF cycles without manual intervention. Intensity is dialed across ten discrete levels and held there. The canopy profile becomes uniform from top to bottom, and the yield gap that was previously invisible becomes measurable — and recoverable.

The mechanism is four 16-inch LED bars, each populated with 18 Samsung LM301H EVO diodes rated at 3.14 µmol/J PPE — a diode platform that outperforms previous-generation Samsung LM301H, LM301B, and Bridgelux 3030 chips in both output per diode and blue-spectrum efficiency. The dual-channel spectrum — 3000K warm white and 5000K cool white — delivers a full-spectrum profile across the entire canopy surface. The included Dimming Schedule Controller manages all four bars simultaneously, with ten intensity levels accessible via manual knob or automated schedule. The unibody aluminum housing dissipates heat passively, protecting diode lifespan without active cooling overhead. The entire kit draws 42W at 100–240V AC, 50/60 Hz, pulling 0.06A — negligible electrical load that integrates into any existing circuit without dedicated infrastructure. In practical terms, the IONBEAM S16 delivers 3.14 µmol/J PPE across four 16-inch bar positions at 42W total system draw, operating at 0.06A on any 100–240V AC circuit.

Where This Belongs (and Doesn't)

Not recommended for circuits under ~0.35A @120V or ~0.18A @240V per fixture, or unsealed rooms lacking HVAC capacity for expected thermal load.

Note: The IONBEAM S16 kit draws 42W at 0.06A on a 100–240V AC circuit. While electrical load is minimal, all supplemental lighting installations in licensed commercial facilities should be verified against local NEC requirements and facility electrical plans by a qualified electrician.

Infrastructure Note: The IONBEAM S16 uses a US Plug (NEMA 1-15 Type-A) power connector. Verify that existing outlet infrastructure in the deployment zone is compatible before installation. UIS platform integration requires a compatible AC Infinity controller hub; third-party device integration is available via RJ11/12 adapter and control plug module.

How It Works

The IONBEAM S16 kit operates as a four-bar supplemental array, with each 16-inch bar (15.98 x 1.12 in. / 40.6 x 2.85 cm) housing 18 Samsung LM301H EVO diodes in a unibody aluminum housing. The aluminum board serves a dual function: it is the substrate for the diode array and the passive thermal management system, conducting heat away from the junction without fans, moving parts, or active cooling infrastructure. This passive dissipation architecture is what enables the 50,000-hour rated lifespan — diode degradation is primarily a thermal event, and the unibody design keeps junction temperatures within the operating envelope across the full duty cycle.

The dual-channel spectrum — 3000K warm white and 5000K cool white — is delivered simultaneously across all four bars, producing a full-spectrum output profile that supports both vegetative and reproductive growth phases without fixture swaps or spectrum changes. Each diode is rated at 3.14 µmol/J PPE, a figure that exceeds the output efficiency of previous-generation Samsung LM301H, LM301B, and Bridgelux 3030 platforms. The higher blue-spectrum content of the EVO diode platform supports canopy penetration and secondary metabolite expression in lateral and lower bud sites that receive reduced photon flux from overhead primary fixtures.

The four bars connect in a daisy-chain configuration using the included 9.1-inch (23.2 cm) connector cords, with the terminal bar connecting to the EC power adapter via the dual-corded bar's male connector. The power adapter feeds the included Dimming Schedule Controller (3.31 x 1.26 in. / 8.4 x 3.2 cm), which manages the entire array across three operating modes: OFF, ON, and SCHEDULE. Ten discrete intensity levels are accessible via manual dimming knob or automated schedule programming. When integrated into the AC Infinity UIS ecosystem via a compatible controller hub, the entire array can be programmed, monitored, and adjusted remotely through the AC Infinity app, including access to automation sequences and climate data correlation. The full kit draws 42W at 100–240V AC, 50/60 Hz, at 0.06A — a load profile that adds no meaningful demand to existing facility circuits. In practical terms, the IONBEAM S16 delivers 3.14 µmol/J PPE across four 16-inch Samsung LM301H EVO bar positions at 42W total draw, with automated schedule control and UIS ecosystem integration available through the included Dimming Schedule Controller.

System Integration

To operate this platform at peak efficiency, verify your ecosystem matches these requirements:

• Controller Compatibility: The included Dimming Schedule Controller manages all four bars with ten intensity levels and OFF/ON/SCHEDULE modes. For full UIS ecosystem integration — including remote app control, automation programming, and climate data correlation — a compatible AC Infinity UIS controller hub is required (sold separately).
• Mounting Infrastructure: Bars mount magnetically to steel surfaces using the included cold-rolled steel bars with matte black powder coating. Verify that the deployment zone contains accessible steel tent frame members or equivalent steel mounting surfaces. Non-steel surfaces require alternative mounting solutions not included in the kit.
• Power Infrastructure: Requires a standard US outlet (NEMA 1-15 Type-A). Input voltage range is 100–240V AC, 50/60 Hz, at 0.06A. No dedicated circuit required; compatible with standard facility outlet infrastructure.
• Environmental Setpoints: Operating humidity range is 35–85% RH. Verify that the deployment zone does not exceed this range under peak humidity conditions. IP65 rating provides ingress protection against water and dust but does not qualify the unit for direct liquid exposure or submersion.
• Third-Party Integration: Third-party grow lights and outlet devices can be integrated into the UIS platform via RJ11/12 adapter and control plug module (sold separately).

Facility Integration Data

The following ROI model and comparison data are provided to support procurement and deployment planning for multi-unit supplemental lighting deployments.

Operator Field Note

• Weight and Structural Load: The complete IONBEAM S16 kit weighs 3.5 lbs. Magnetic mounting to tent frames is toolless, but verify that the tent frame steel is sufficient gauge to hold the magnetic attachment under vibration or airflow conditions present in the facility.
• Electrical Draw: System draws 0.06A at 42W on a 100–240V AC, 50/60 Hz circuit. This load is negligible on any standard facility outlet circuit; however, confirm outlet availability and NEMA 1-15 Type-A compatibility at the deployment zone before installation.
• Power Cord Length: Primary power cord length is 99.8 in. (253.4 cm) for the full kit assembly. Connector cord between bars is 9.1 in. (23.2 cm). Plan bar positioning and outlet proximity accordingly before mounting.
• Environmental Limits: Operating humidity range is 35–85% RH. Do not deploy in zones where humidity regularly exceeds 85% RH, even with IP65 ingress protection in place. IP65 rating addresses water and dust ingress, not sustained condensation or saturation events.
• Certification Status: This product does not carry ETL or UL listing per manufacturer source data. Verify that your facility's AHJ and insurance carrier accept non-listed supplemental lighting equipment before permanent installation in licensed commercial environments.
• Daisy-Chain Configuration: Bars connect in sequence using the included connector cords. Follow the manufacturer's connection sequence: single-corded bar female port connects to dual-corded bar male connector; power adapter connects to the dual-corded bar's remaining port; power adapter then connects to the Dimming Schedule Controller.

Shipping & Logistics

• Origin: Ships from Cannafull Spectrum Solutions' authorized distribution point within the contiguous 48 United States. This product is not available for shipment to Alaska, Hawaii, or international destinations.
• Processing: Orders are processed within 1–2 business days of confirmed payment. Lead time per manufacturer source data is 1–2 business days.
• Damage: Inspect all shipments within 48 hours of delivery. Document any damage with photographs and contact Cannafull Spectrum Solutions at (888) 378-0017 or sales@cannafullspec.com within 48 hours of receipt. Claims reported after this window may not be eligible for carrier damage resolution.
• Returns: Units in original, uninstalled condition may be returned within 30 days of delivery. A Return Authorization (RA) number issued by Cannafull Spectrum Solutions is required before any return shipment is made.
• Restocking Fee: Returns of non-defective items are subject to a restocking fee of up to 25% per our Return Policy. Review full terms at cannafullspec.com/pages/return-policy before ordering.

Questions? (888) 378-0017 or sales@cannafullspec.com

What's in the Box

• 4x IONBEAM S16 LED grow light bars (16-inch, Samsung LM301H EVO, full spectrum)
• 4x Cold-rolled steel mounting bars with matte black powder coating
• 1x Dimming Schedule Controller (3.31 x 1.26 in. / 8.4 x 3.2 cm)
• 1x EC power adapter with male connector
• Connector cords for daisy-chain bar assembly (9.1 in. / 23.2 cm between bars)
• Power cord (99.8 in. / 253.4 cm, US Plug NEMA 1-15 Type-A)

Note: Box contents are based on available manufacturer data. Verify complete contents upon receipt. Contact Cannafull Spectrum Solutions at (888) 378-0017 if any components are missing or damaged.

Regional Compliance & Deployment Notes

Commonly deployed in sealed commercial cultivation facilities across the United States. Installation, HVAC sizing, and electrical requirements vary by jurisdiction; always verify with local code.