Rollo de película Mylar AC Infinity | Lámina reflectante PET | 4 x 50 pies

Quick Spec: 4.00 ft. x 50.00 ft. (121.92 x 762 cm) | 0.05 mm thickness | PET material | Double-sided reflective surface | SKU: AC-PRA50

Precision Control in Any Space

Every lumen your fixtures produce that never reaches a leaf is revenue that never reaches your operation. In enclosed cultivation environments, uncontrolled light scatter is a silent, continuous tax — photons absorbed by bare concrete, flat-painted drywall, or degraded single-sided foil that yellows and delaminates under sustained thermal load. The result is uneven canopy density, edge-zone deficiency, and a fixture investment that is performing at a fraction of its installed capacity. No additional wattage compensates for a room that is structurally leaking light, and no scheduling protocol corrects for a reflective surface that has already failed.

After deployment, the geometry of the room changes. Walls and floors that previously absorbed and scattered photons become active contributors to the canopy's light budget. Edge zones that historically underperformed relative to center-canopy positions begin receiving redirected flux, compressing the variance between the highest- and lowest-lit positions in the room. The facility operates with the same fixture count and the same electrical draw — but the photon delivery architecture is no longer losing output to structural dead zones.

The mechanism is the material itself. AC Infinity's Mylar Film (AC-PRA50) is constructed from 0.05 mm PET — polyethylene terephthalate — a thermostable, tear-resistant substrate that maintains dimensional stability under the elevated temperatures and humidity cycles characteristic of active cultivation environments. The double-sided reflective surface is engineered to redirect incident light rather than absorb it, expanding effective grow lighting coverage across the full 4.00 ft. x 50.00 ft. (121.92 x 762 cm) roll. The film is lightweight, portable, and field-cuttable, allowing operators to fit it to walls, floors, partitions, and enclosures without specialized tooling. In practical terms, the AC Infinity Mylar Film AC-PRA50 delivers a double-sided reflective surface across a 200 sq. ft. deployable area from a single 0.05 mm PET roll measuring 4.00 ft. x 50.00 ft.

Where This Belongs (and Doesn't)

This product is a passive reflective surface material. It does not require electrical connection, HVAC integration, or controller pairing. Installation involves mechanical fastening or adhesive mounting only. Consult your facility's structural and fire-safety guidelines before applying reflective film to surfaces adjacent to high-heat fixtures or electrical panels.

How It Works

The AC Infinity Mylar Film operates on a straightforward optical principle: surfaces with high reflectivity redirect incident photons back into the cultivation zone rather than converting them to heat or absorbing them into the substrate. The 0.05 mm PET construction provides the structural integrity necessary to maintain a flat, wrinkle-minimized surface — critical because surface irregularities in reflective film scatter light diffusely rather than directing it back toward the canopy. A smooth, taut installation maximizes the directional component of the reflected flux.

The double-sided reflective surface means the film performs regardless of which face is oriented toward the light source — a practical advantage in partition and divider applications where both faces may be exposed to fixture output from adjacent zones. The PET substrate is thermostable, meaning it does not deform, delaminate, or off-gas under the sustained elevated temperatures common in sealed cultivation rooms. Tear resistance ensures the material survives repeated installation, repositioning, and cleaning cycles without structural failure. The film is field-cuttable to any dimension, allowing precise fitting around electrical conduit, HVAC penetrations, and structural framing without waste. In practical terms, the AC Infinity Mylar Film AC-PRA50 delivers a thermostable, double-sided reflective PET surface across a 4.00 ft. x 50.00 ft. deployable area at 0.05 mm thickness, field-cuttable to any facility dimension.

System Integration

• Lighting Systems: Compatible with all fixture types — LED, HID, CMH, and fluorescent — as a passive reflective surface requiring no electrical integration.
• Environmental Controllers: No controller pairing required; the film operates passively within any AC Infinity UIS-managed or third-party controlled environment.
• HVAC and Atmospheric Control: Field-cuttable design accommodates penetrations for ducting, sensor wiring, and HVAC supply/return without compromising surface coverage.
• Vertical and Multi-Tier Systems: Roll format and lightweight construction support deployment across multi-tier rack systems, partition walls, and floor coverage in high-density configurations.
• Cleaning and Maintenance Cycles: Smooth PET surface is compatible with standard facility sanitation protocols — wipe-down cleaning without material degradation.

Facility Integration Data

The table below models reflective film coverage requirements and material cost at scale for facilities deploying the AC-PRA50 across multiple rooms or zones — use it to estimate roll count against your total reflective surface area target.

Operator Field Note

• Surface Preparation: Clean and dry the mounting surface before installation — dust, moisture, or residue under the film will cause air pockets that reduce surface contact and create reflective irregularities.
• Cutting Protocol: Use a straight edge and sharp utility blade for clean cuts. Ragged edges do not affect reflective performance but create debris that can contaminate the cultivation environment.
• Thermal Clearance: Maintain manufacturer-recommended clearance distances between the film surface and any high-radiant-heat fixture. The PET substrate is thermostable but is not rated for direct contact with open-heat sources.
• Sanitation Compatibility: The smooth PET surface wipes clean with standard facility sanitation solutions. Avoid abrasive scrubbing pads that can micro-scratch the reflective surface and reduce efficiency over time.
• Double-Sided Utility: In partition applications, both faces of the film are reflective — orient installation to take advantage of this in zones where fixtures illuminate from multiple directions.
• Roll Storage: Store unused roll sections in a cool, dry location away from direct UV exposure to preserve reflective surface integrity between deployment cycles.

Operator FAQ

Shipping & Logistics

• Shipping Zone: Cannafull Spectrum Solutions ships within the contiguous 48 United States only. Alaska, Hawaii, U.S. territories, and international destinations are not served.
• Carrier & Transit: Standard ground shipping applies. Transit times vary by destination zone. Expedited options may be available at checkout.
• Returns: Returns are accepted in accordance with the Cannafull Spectrum Solutions Return Policy. Items must be in original, uninstalled condition. Review full terms at cannafullspec.com/pages/return-policy before ordering.
• Restocking Fee: Returns of non-defective items are subject to a restocking fee of up to 25% per our Return Policy. Review full terms at cannafullspec.com/pages/return-policy before ordering.

Questions before ordering? Contact Cannafull Spectrum Solutions at cannafullspec.com — our team supports licensed operators across the United States.

What's in the Box

• 1x AC Infinity Mylar Film Roll — 4.00 ft. x 50.00 ft. (121.92 x 762 cm), 0.05 mm PET, double-sided reflective surface (SKU: AC-PRA50)

Box contents confirmed from manufacturer source data. Mounting hardware, adhesives, and installation tools are not included and must be sourced separately. If your shipment is missing any listed item, contact Cannafull Spectrum Solutions at cannafullspec.com before opening a return.

Regional Compliance & Deployment Notes

• Material Classification: The AC-PRA50 is a passive reflective surface material (PET film). It does not contain electrical components, controlled substances, or regulated chemical compounds requiring special handling documentation under standard U.S. shipping regulations.
• Fire Safety: Before installation in licensed cultivation facilities, verify that reflective film use on walls, ceilings, and floors complies with your jurisdiction's fire safety and building codes. Some jurisdictions impose restrictions on reflective or combustible surface materials in commercial structures.
• Facility Licensing: This product is sold for use in lawfully licensed cultivation and horticultural facilities. Buyers are solely responsible for ensuring that their facility operations comply with all applicable federal, state, and local regulations.
• Shipping Jurisdiction: Available for purchase and delivery within the contiguous 48 United States only through Cannafull Spectrum Solutions. No shipments to Canadian provinces or international destinations.
• No Controlled Substance Classification: The AC-PRA50 Mylar Film is an agricultural supply product with no controlled substance classification under U.S. federal law. No DEA, FDA, or state cannabis board pre-approval is required to purchase or possess this product.

Compliance requirements vary by state, county, and municipality. The information above is provided as a general reference only and does not constitute legal advice. Cannafull Spectrum Solutions makes no representations regarding the suitability of this product for any specific licensed facility's regulatory environment. Consult your compliance officer or legal counsel before deployment in regulated cultivation operations.