Cúpula de humedad AC Infinity | Kit de propagación con extensión de altura | Bandeja de celdas de 5 x 8

Quick Spec: 14.24 in. L × 9.09 in. W | Standard Height: 6.57 in. | Extended Height: 10.70 in. | Capacity: Up to 40 seedlings | Vents: 4 adjustable rotating vent disks | Material: PS Plastic (Gloss Finish) | SKU: AC-HDA5

Precision Control in Any Space

Every propagation failure has the same root cause: an environment that drifts. Humidity climbs unchecked, then crashes when a vent is cracked too far. Fixed-height domes choke taller cuttings before they establish. Trays without drainage management turn standing water into a contamination vector. These are not random losses — they are the predictable output of equipment that was never designed to hold a parameter, and every failed cutting or uneven seedling tray represents time, genetics, and labor that cannot be recovered.

After deployment, the propagation bench operates as a defined atmospheric zone. Humidity is dialed in and held through rotating vent disks that respond to operator input without requiring tray removal or dome repositioning. Cuttings with vertical clearance requirements are accommodated by extending the dome ceiling rather than being forced into a geometry that stresses them. Drainage is managed at the tray level, not by the operator mopping up overflow. The result is a propagation cycle where variables are controlled, not tolerated.

The mechanism behind that control is a purpose-built enclosure architecture: a gloss-finish PS plastic dome spanning 14.24 in. L × 9.09 in. W, with a standard interior height of 6.57 in. that extends to 10.70 in. via included height extension panels — each panel adding additional adjustable vent disks to the airflow management system. Four rotating vent disks provide dual-axis humidity regulation without requiring dome removal. The 5×8 cell grid seedling tray supports up to 40 seedlings with built-in excess water drainage, and the base tray catches overflow to prevent bench contamination. In practical terms, the AC-HDA5 delivers a regulated propagation enclosure for up to 40 seedlings across a 14.24 in. × 9.09 in. footprint with an extendable ceiling height of 10.70 in.

Where This Belongs (and Doesn't)

The AC-HDA5 is a passive atmospheric enclosure. It does not include active heating, active humidity injection, or electronic controls. Integration with active environmental controllers (e.g., AC Infinity CONTROLLER series) is operator-configured and not included. Verify bench clearance and environmental controller compatibility before deployment.

How It Works

The AC-HDA5 operates as a closed-loop atmospheric enclosure through the interaction of four engineered subsystems. The gloss-finish PS plastic dome creates a sealed microclimate over the seedling tray, trapping transpired moisture and ambient humidity to elevate and stabilize the vapor pressure deficit within the enclosure — a critical parameter for root initiation in cuttings and uniform germination in seedlings.

Humidity regulation is managed through four adjustable rotating vent disks mounted in the dome surface. Rotation opens or closes the vent aperture in a smooth, continuous motion — allowing operators to set a precise exchange rate between the internal microclimate and the ambient room environment without removing the dome or disturbing the tray. This is the mechanism that eliminates the binary choice between "sealed and overhumid" or "open and uncontrolled" that defines fixed-vent or no-vent enclosures.

Vertical clearance is addressed by the included height extension kit. Two vented side panels and two additional side panels bolt to the base of the dome using the included bolt and wing nut hardware, raising the interior ceiling from 6.57 in. to 10.70 in. The extension panels include additional vent apertures, increasing total airflow management capacity as ceiling height increases — a design decision that prevents the extended configuration from becoming a stagnant high-humidity trap. The 5×8 cell grid seedling tray organizes up to 40 individual propagation sites with structural separation between cells, and the base tray's built-in drainage system captures excess water at the tray level, preventing overflow from reaching the bench surface. In practical terms, the AC-HDA5 delivers a dual-configuration propagation enclosure — 6.57 in. standard or 10.70 in. extended — across a 14.24 in. × 9.09 in. footprint with four-point rotating vent control and 40-cell seedling capacity.

Commercial Assurance

System Integration

• Environmental Controller Compatibility: The AC-HDA5 enclosure is compatible with AC Infinity's CONTROLLER ecosystem for operators who want to automate ambient room conditions feeding the dome's microclimate — controllers are sold separately and not included.
• Propagation Light Integration: The gloss PS plastic dome is transparent, allowing overhead propagation lighting (T5, LED propagation bars) to penetrate the dome surface for light saturation without dome removal.
• Tray System Compatibility: The included seedling tray and base tray are purpose-matched to the AC-HDA5 footprint; third-party tray substitution may compromise drainage alignment and dome seal integrity.
• Bench Footprint Planning: The 14.24 in. × 9.09 in. base footprint allows multi-unit deployment on standard propagation benches; operators running parallel clone programs can stage multiple AC-HDA5 units in a single bench row.
• Extension Kit Pre-Installed Option: The height extension panels can be pre-installed at setup or added mid-cycle; the bolt and wing nut fastening system allows reconfiguration without tools beyond hand-tightening.

Facility Integration Data

The following ROI reference table is provided for operators evaluating multi-unit propagation bench deployment. All figures are based on published unit pricing of $69.99 USD per AC-HDA5 and assume full kit configuration including height extension hardware.

Operator Field Notes

• Vent Calibration at Setup: Set all four rotating vent disks to a partially open position at initial deployment and adjust incrementally over the first 24–48 hours based on observed condensation on the dome interior — heavy condensation indicates insufficient exchange; rapid drying indicates over-venting.
• Extension Kit Deployment Timing: Install height extension panels before cuttings exceed 4 in. in height; retrofitting the extension mid-cycle risks disturbing root zones and disrupting the established microclimate.
• Drainage Inspection Cadence: Inspect the base tray drainage accumulation every 48 hours during active propagation cycles; standing water in the base tray beyond 72 hours increases pathogen pressure regardless of humidity control at the dome level.
• Dome Transparency Maintenance: Clean the PS plastic dome surface with a non-abrasive, pH-neutral solution between propagation cycles; scratching the gloss finish reduces light transmission and compromises visual monitoring of seedling progress.
• Multi-Unit Bench Spacing: When deploying multiple AC-HDA5 units on a shared bench, maintain a minimum 2 in. gap between units to allow ambient airflow around each enclosure and prevent cross-contamination of microclimate zones.
• Hardware Torque on Extension Panels: Tighten bolt and wing nut hardware to hand-tight only; over-torquing the PS plastic panel connection points risks stress fractures at the fastener seats, which compromises dome seal integrity.

Operator FAQ

Shipping & Logistics

• Shipping Jurisdiction: Cannafull Spectrum Solutions ships within the contiguous 48 United States only. Orders to Alaska, Hawaii, U.S. territories, or international destinations cannot be processed through this channel.
• Freight Class: The AC-HDA5 ships as a standard parcel. No freight or LTL classification is required for single-unit orders. Multi-unit fleet orders — contact Cannafull Spectrum Solutions for consolidated shipping options.
• Returns: Returns are accepted subject to Cannafull Spectrum Solutions return policy terms. Units must be returned in original, uninstalled condition with all included components. Defective units are handled under AC Infinity Inc. manufacturer warranty procedures.
• Restocking Fee: Returns of non-defective items are subject to a restocking fee of up to 25% per our Return Policy. Review full terms at cannafullspec.com/pages/return-policy before ordering.

For order support, volume pricing, or logistics coordination: contact Cannafull Spectrum Solutions directly via cannafullspec.com.

What's in the Box

The following components are confirmed included with every AC-HDA5 unit as specified in manufacturer source documentation:

• Humidity Dome — ×1
• Base Tray — ×1
• Seedling Tray (5×8 cell grid, up to 40 seedlings) — ×1
• Vent Disks (adjustable rotating) — ×4
• Vented Panel (height extension) — ×2
• Side Panel (height extension) — ×2
• Bolt and Wing Nuts (extension hardware) — ×8

Component list reflects manufacturer-published bill of materials for SKU AC-HDA5 (UPC: 819137023208). Cannafull Spectrum Solutions does not modify, repackage, or substitute components. If any component is missing upon receipt, contact Cannafull Spectrum Solutions before use. Propagation media, rooting compounds, and environmental controllers are not included and are sold separately.

Regional Compliance & Deployment Notes

• Jurisdiction: The AC-HDA5 is sold for use within the contiguous 48 United States. Cannafull Spectrum Solutions does not ship to Canadian provinces, U.S. territories outside the contiguous 48 states, or international destinations.
• Regulatory Use Context: This product is a passive propagation enclosure with no electrical components. It does not require electrical permits, HVAC certification, or licensed installation. Operators are responsible for ensuring propagation activities comply with applicable state and local cultivation licensing requirements.
• Facility Compliance: The AC-HDA5 does not carry a specific electrical or safety certification listing (UL, ETL, or equivalent) as it contains no powered components. Operators in licensed facilities should verify that propagation equipment procurement aligns with their facility's compliance documentation requirements.
• State Cultivation Licensing: Propagation of regulated plant species must be conducted in accordance with the operator's current state-issued cultivation license. Cannafull Spectrum Solutions makes no representation regarding the licensing status of any purchaser or the regulatory compliance of any specific propagation application.

Regional compliance information is provided for general operator reference only and does not constitute legal or regulatory advice. Licensing requirements vary by state and are subject to change. Operators are solely responsible for verifying current compliance obligations with the relevant state regulatory authority prior to deployment. Cannafull Spectrum Solutions assumes no liability for regulatory non-compliance arising from the use of this product.