AC Infinity IONBEAM U4 | 目标光谱 UV LED 生长灯条 | 4 条套装 | 11 英寸

Key Specs: 48W | 365nm + 395nm UV | 4x4 / 5x5 ft coverage (4 bars) | 0.06A @ 100–240V | 3.8 lb | 2-Year Warranty

Stop Buying. Start Manufacturing Top-Shelf Inventory.

The silent cost of guesswork-driven growing is not a single bad harvest — it is the cumulative erosion of output quality across every cycle you run without a controlled UV protocol. Consumer-grade equipment delivers inconsistent spectrum coverage, no scheduling architecture, and no integration with the rest of your environmental control stack. The result is canopy variance you cannot measure, expression triggers you cannot reliably activate, and a quality ceiling you cannot break through because the inputs are never the same twice. Every cycle run without deliberate UV deployment is a cycle where secondary metabolite expression is left to chance.

After deploying the IONBEAM U4, the facility operates on a different logic. UV supplementation runs on a programmed schedule — same intensity, same duration, same canopy coverage, every cycle. The four bars distribute 365nm and 395nm UVA evenly across the entire 4x4 or 5x5 footprint, activating during the fruit and flower stages when expression triggers matter most. The controller handles the timing. The UIS ecosystem handles the integration. The operator handles the harvest.

The mechanism is a four-bar array of Samsung LM301H EVO diodes — 12 diodes per bar, 48 diodes total — emitting at 365nm and 395nm to deliver targeted UVA coverage across 4x4 and 5x5 spaces. The included dimming schedule controller provides ten intensity levels and OFF/ON/SCHEDULE modes, enabling automated UV deployment without manual intervention each cycle. The unibody aluminum housing dissipates heat passively, protecting diode longevity across a rated 50,000-hour lifespan. IP65 construction handles operating humidity up to 85% RH without degradation. Magnetic mounting ends allow toolless repositioning on any steel surface, and the included cold-rolled steel bars extend that mounting flexibility to any grow tent frame. The entire platform connects into the UIS ecosystem for centralized controller management and AC Infinity app automation. In practical terms, the IONBEAM U4 delivers targeted 365nm and 395nm UVA coverage across 4x4 and 5x5 footprints at 48W draw, 0.06A, on a programmable ten-level dimming schedule.

Where This Belongs (and Doesn't)

This kit draws 48W at 0.06A on 100–240V AC. Verify that your supplemental lighting circuit is properly rated and that your facility's environmental control system can account for the additional thermal load before installation.

Infrastructure Note: The IONBEAM U4 is a supplemental UV system and requires an existing primary lighting platform. It does not replace full-spectrum grow lighting. For multi-room deployments, calculate one 4-bar kit per 4x4 or 5x5 canopy zone. UIS controller integration requires a compatible AC Infinity controller hub (sold separately).

How It Works

Each of the four IONBEAM U4 bars is built on a unibody aluminum housing that serves dual functions: it positions 12 Samsung LM301H EVO diodes per bar in a linear array optimized for even UVA distribution, and it passively dissipates the thermal load generated during operation to protect diode integrity over the rated 50,000-hour lifespan. The diode selection is deliberate — 365nm deep UV and 395nm near-UV target the UVA band that research associates with secondary metabolite expression during fruit and flower development stages. This is not broadband UV; it is a two-wavelength targeted deployment designed to activate specific physiological responses at the canopy level.

The included dimming schedule controller manages all four bars simultaneously, offering ten discrete intensity levels and three operating modes: OFF, ON, and SCHEDULE. SCHEDULE mode enables automated daily UV deployment — operators program the on/off window once, and the system executes it every cycle without manual intervention. For facilities running UIS ecosystem infrastructure, the controller integrates with the central AC Infinity controller hub and app, enabling synchronized management of UV supplementation alongside climate, ventilation, and primary lighting schedules from a single interface. Magnetic mounting ends on each bar allow toolless attachment to any steel surface; the included cold-rolled steel bars with matte black powder coating provide mounting bases for tent frames that lack direct steel contact points. IP65 construction across all four bars ensures resistance to water and dust ingress at operating humidity levels up to 85% RH. In practical terms, the IONBEAM U4 delivers targeted 365nm and 395nm UVA from 48 Samsung LM301H EVO diodes across 4x4 and 5x5 footprints, controlled by a ten-level programmable schedule controller, at 48W and 0.06A draw.

System Integration

To operate this platform at peak efficiency, verify your ecosystem matches these requirements:

• Controller Compatibility: The included dimming schedule controller operates the four bars in standalone mode. For UIS ecosystem integration, a compatible AC Infinity controller hub (sold separately) is required to enable app-based automation and synchronized device management.
• Primary Lighting: The IONBEAM U4 is a supplemental UV system. A full-spectrum primary lighting platform must already be in place. UV supplementation is additive — it does not replace PAR delivery from your primary fixture.
• Mounting Surface: Magnetic mounting requires steel contact surfaces. Included cold-rolled steel bars extend compatibility to non-steel tent frames. Verify structural capacity of your frame before mounting all four bars.
• Power Circuit: 100–240V AC, 50/60 Hz, 0.06A. Confirm your supplemental lighting circuit is rated for the additional load when running alongside primary fixtures and climate control equipment.
• Environmental Setpoints: Operating humidity range 35–85% RH. Verify your facility's atmospheric control maintains humidity within this range at the bar mounting height.

Facility Integration Data

The following data supports fleet-level procurement decisions and direct comparison against legacy supplemental UV approaches for licensed cultivation operations.

Operator Field Note

• Weight and Structural Load: Total kit weight is 3.8 lb across four bars plus controller. Verify that your tent frame or mounting surface can support the distributed load of all four bars simultaneously, particularly when using the included steel mounting bars.
• Electrical Draw: 48W total at 0.06A, 100–240V AC, 50/60 Hz. This is a low-draw supplemental system; however, always account for cumulative circuit load when running alongside primary lighting, fans, and climate control equipment.
• UV Exposure Warning: These bars emit 365nm and 395nm UVA radiation. Do not look directly at operating bars without appropriate UV-protective eyewear. Limit direct skin exposure during operation. Ensure personnel are clear of the canopy zone when bars are active at high intensity levels.
• Environmental Setpoints: Operating humidity range is 35–85% RH. Operating outside this range may affect diode performance and long-term lifespan. Confirm your atmospheric control system maintains humidity within spec at bar mounting height.
• Cord Management: Power cord length is 99.8 in. (253.4 cm); connector cord length is 9.1 in. (23.2 cm). Plan cable routing before installation to avoid tension on connectors and interference with canopy airflow.
• Controller Dimensions: The included controller measures 3.31 x 1.26 in. (8.4 x 3.2 cm). Mount in a location accessible for schedule programming but protected from direct water contact during irrigation cycles.

Shipping & Logistics

• Origin: Ships from Cannafull Spectrum Solutions within the contiguous 48 United States. This product is not available for shipment to Alaska, Hawaii, or international addresses.
• Processing: Orders are processed within 1–2 business days of receipt. Tracking information is provided upon shipment.
• Damage: Inspect all shipments upon delivery. Report any shipping damage within 48 hours of receipt by contacting Cannafull Spectrum Solutions at (888) 378-0017 or sales@cannafullspec.com. Retain all original packaging materials for freight claims.
• Returns: Free and easy returns accepted within 30 days of delivery. A Return Authorization (RA) number is required before returning any item. Contact our team to initiate the RA process.
• Restocking Fee: Returns of non-defective items are subject to a restocking fee of up to 25% per our Return Policy. Review full terms at cannafullspec.com/pages/return-policy before ordering.

Questions? (888) 378-0017 or sales@cannafullspec.com

What's in the Box

• 4x IONBEAM U4 UV LED light bars (10.98 x 1.08 in. / 27.9 x 2.75 cm each)
• 1x Dimming schedule controller (3.31 x 1.26 in. / 8.4 x 3.2 cm)
• Cold-rolled steel mounting bars with matte black powder coating
• Power cord (99.8 in. / 253.4 cm, US Plug NEMA 1-15 Type-A)
• Connector cord (9.1 in. / 23.2 cm)

Note: Box contents are based on available manufacturer data. Verify complete contents upon receipt. Contact Cannafull Spectrum Solutions at (888) 378-0017 if any components are missing or damaged.

Regional Compliance & Deployment Notes